Need a Plumber in Fort Worth, TX? Call Free (888) 498-1723

Sunday, March 20, 2011

How to repair a radiator valve

If you see a leaking valve in your radiator, it is not necessary to call a professional plumber. In most cases, a few simple but effective resolve the matter.

Tools and materials needed:
- A screwdriver.
- An adjustable wrench.
- If necessary teflon sealant.

Remove the valve handle.

- Start by removing the valve handle by unscrewing or unclipping the.

Tighten the nut tap.

- If the nut of the valve is open, tighten using the wrench. You compress and seal the valve, which is likely to stop the leak.
- If the leak is not repaired, it will then consider stopping the boiler and drain the radiator to remove the valve.

Replace the seal or close the leak.

- Remove the tap and then look where does the fault.
- If it is a joint leak, then replace the teflon inside the joint.
- If it's a hole, then seal with putty cold.

Unclog a sink

A stopper in a sink is easy to spot: the water drains hardly and water can stagnate in the bottom of the sink. Several solutions exist to overcome this situation.

Materials needed: 
- The chemical unblocker;
- Or a suction cup;
- Or an adjustable wrench and a bucket; 
- Or a ferret.
 

The chemical unblocker 

The first solution, the most commonly considered is the chemical unblocker. They come in different forms: liquid, solid or gel.
 

Simply pour the correct amount of product and it will remove impurities. Suffice it then rinse by pouring water into the drain.
 

This solution is very simple and very fast, but be careful because they are highly toxic and can damage the plastic parts of the pipes. Read very carefully the user manual, and take all necessary precautions by wearing gloves to prevent burns.
 

If the chemical solution does not come at the end of the plug, try the cup. Before you begin, make sure that all of the chemical was eliminated because in case of splashes when handling the cup, you may be splashing and burns.
 

The suction cup

First, know that we must plug the overflow with a damp cloth so that air does not pass. Then:
- Fill the bottom of the sink so that water covers the rubber suction cup;

- Put the plunger over the drain; 
- Press down firmly and then lift the cup so that there is a call for air; 
- Repeat this movement until the sink is completely empty.
 

An alternative, more radical, is to dismantle the trap.
 

Disassemble the trap

The trap is a device located under the sink between the drain and the pipe. Its role is to permanently retain the water used to stop the lift smells of the discharge pipe. It is either presented as S (elbow) or bottle (full).
 

Traps are the most recent bleed screw, which makes it much easier surgery.Thus:
- Put a bucket under the trap to retrieve water from the latter;
- Unscrew the trap;
- Dispose of the waste causing the plug and tighten it after cleaning, be careful and do not forget the gasket, probably fell into the basin during unscrewing.

For older, it will remove the entire trap. To do this:
- Equip yourself with a wrench and unscrew the nuts or rings that hold the trap binding, do not hesitate to protect the nuts with tape to avoid damaging the surface; 

- Finish unscrewing by hand; 
- Disposing of waste in the trap causing the cap;
- Remount the beginning with the nuts by hand, then get yourself a pair of pliers to tighten.
 

If the cap is beyond the siphon, there is another solution: the ferret.
 

Ferrets 

The ferret is a tool with a flexible metal rod and whose end is covered with tiny brushes or wire shaped corkscrew. By rotary motion, ferret hanging waste and destroys the cluster.
 

For efficient use of the ferret, follow these steps: 
- First, make sure that the ferret's head passes easily through the elbow of the siphon because it should not get stuck or if the ferret does not pass or that the stem is too short, remove the trap to pass the rod through the opening; 
- Operate the ferret until it touches the stopper. This will be achieved when the rod is harder to turn and that the tool does not advance at all; 
- Ferrets out of the pipe, the waste piles since the end of his head;
- Run water at high pressure to make sure everything was removed.
 

How to unclog a toilet?

If toilets are clogged, you may need to call a plumber. Read below  how to improve the situation.

Materials:
- A pair of medical gloves
- A suction cup for toilet

Especially, do not shoot more flush: it could overflow the toilet or filling them even more!

First check the water tank. If it is clogged, it will start with his lead pipe.

Otherwise, use the suction cup, placing the tip at the bottom of the plastic toilet and make sure that air does not pass, to benefit from the suction effect.

Next, make up the air with the call. Optionally, you must repeat this process until the toilets are opportunities.